Tricks of the Trade: Continuous Bound Sleeve Placket

A continuous bound placket is one of my favourite methods for a sleeve placket where lightweight fabrics are used, such as on a blouse or dress.  It is easily inserted into a one piece sleeve where a vertical split is made – not at the sleeve seam, but at the location of the little finger.

You will need to cut the binding twice the length of the split, and a cut width of 25mm  (1″) will give a finished width of 6mm (1/4″).  The binding is easier to sew if it is cut on grain, not the bias. If you are sewing checks or stripes, then cutting on the bias is a good idea to avoid pattern matching.

Here I have opened out the sleeve split and laid it over top of the binding, with the right side of the binding to the wrong side of the sleeve.  The raw edges align at either end of the split, but at the apex of the split they are offset by 5mm – this is how it will be sewn:

Stitch using a 6mm (1/4″) seam width towards the apex of the split…
…where you leave the needle down to reposition the fabric, and continue stitching to the other end.
 It should look like this:
From the right side of the sleeve, turn the long unattached edge of the binding in 6mm (1/4″), and fold it over again to just overlap your previous stitching. Edgestitch the binding down along its length.

If you are finding this a bit tricky – sew the first few stitches and stop with your needle down, then you can position your fabric again.  Making the binding taut by pulling it slightly towards you helps to form an even binding width.  Pull both top and bottom layers evenly so that the binding does not twist like a rope.

It is best not to press the edge down first, with a bit of practise you will actually achieve a neater result if it is pressed after you have edgestitched.

Now fold the binding in half with the right sides of sleeve together, and backtack diagonally across the fold like so:
The finished binding will look like this:
The front side will be folded under as it is inserted into the cuff…
…and the back remains flat when it is inserted into the cuff:
Now all that is needed is to sew the buttonhole and button.  When the cuff is buttoned, the placket is practically invisible and looks just like a tuck in the fabric.
And if you are wondering how to sew the cuff on, there is a tutorial for that too!

Posted by

Designer, Patternmaker, Blogger Of All Things Sewing. Follow as I share projects, patterns, and my favourite tricks of the trade.

18 thoughts on “Tricks of the Trade: Continuous Bound Sleeve Placket

  1. I love your tutorials! I essentially learned to sew by following pictures in books. Even though I've been sewing for eons, I figure there's always a better, faster way to do things. I'll have to try your method with no pins (scary!)


  2. I hate sewing these.. but you make it look easy! You have the best tutorials. I always send people to your invisible zipper one!

    Are you sewing on an industrial machine there? Just curious!


  3. Yes, thanks Sherry – I too love your tutorials and have learnt so much. I haven't had need to do this method, but when the time comes, I know where to go – your site. Again, thanks for sharing.


  4. Aha! I have always cut the strip on the bias – brain goes “binding must be bias”! Of course it never occurred to me that a straight edge doesn't need the stretch of bias duh!
    Many thanks!


  5. I'm glad the tutorials are helpful – photos are so much easier to follow than those diagrams on the pattern sheets aren't they!
    ~Tasia – yes I'm using an industrial machine, one with a lovely brown formica top!
    ~sandra – you could use the bias for effect, eg stripes, but yes straight grain is much easier!


  6. Thanks very much for this! I knew about attaching the binding, but the little dart and folding the front side under is new to me. I might use the continuous placket more often instead of the full-on placket now I know how to make it sit flat.


  7. Hello Sheryll,
    Thank you so much for this, it was really helpful. The tip of sewing the diagonalacroos the fold at the top was great. How about a tutorial on a shirt yoke please! Lydia


Leave a Reply to ~Sherry~ Cancel reply

Fill in your details below or click an icon to log in: Logo

You are commenting using your account. Log Out /  Change )

Facebook photo

You are commenting using your Facebook account. Log Out /  Change )

Connecting to %s

This site uses Akismet to reduce spam. Learn how your comment data is processed.